Sensors

L298P Motor Driver Shield

SKU: 815842 L298P based Arduino motor driver shield Forward, Backward steering indicators Can Drive 2 DC Motors Up to 2A of Maximum Current

150 RPM BO Motor- L Shape

SKU: 2166 Low density: lightweight, low inertia. Capability to absorb shock and vibration as a result of elastic compliance. Ability to operate with minimum or no lubrication, due to inherent lubricity. The relatively low coefficient of friction. Operating Voltage(VDC): 3~12 Shaft Length (mm): 8.5 Shaft Diameter (mm): 5.5 (Double D-type) No Load Current: 40-180mA. Rated Speed(After Reduction): 150 RPM Rated Torque: 0.8 Kgcm

TowerPro MG995 Metal Gear Servo Motor (360° Continuous Rotation)

SKU: 5770 Model: MG995 Weight: 55 gm Operating voltage: 4.8V~ 7.2V Servo Plug: JR Stall torque @4.8V : 9.4kg-cm Stall torque @6.6V : 11kg-cm

150RPM 12V Low Noise Dc Motor With Metal Gears – Grade A

SKU: 1137798 The metal gears have better wear and tear properties. The gearbox is sealed and lubricated with lithium grease and requires no maintenance. Although the motor gives 150 RPM at 12V, the motor runs smoothly from 4V to 12V and gives a wide range of RPM, and torque. The shaft has a hole for better coupling. Operating Voltage(V): 12 Rated Torque(kg-cm): 2 Stall Torque(kg-cm): 7.8

Stepper Motor(28YBJ-48) with ULN2003 Driver Board

SKU: TIFCB0064 This is Stepper Motor(28YBJ-48) with ULN2003 Driver Board 5-wire phase can drive ordinary uln2003 chip can also be connected as phase 2 may be supporting the development board Stepper motor with a standard interface, when used directly pluggable. A, B, C, D four-phase LED indicator which indicates the status of the stepper motor work. Compact size stepper motor perfect for small robotics applications.

FS1000A 433mHz Tx & Rx RF Radio Module

SKU: 16910 Wide input supply (2.5 V to 12V) Easy to integrate (V+, GND, and Data) The device in deep sleep mode when Data pin is grounded Very small dimension.

RC522 RFID Reader Writer SPI Module with Card & Tag Rated

SKU: 9141 Voltage: DC 3.3V (Do not use 5V supply) Operating Current :13-26mA Idle Current :10-13mA Operating Frequency: 13.56MHz Highly integrated analog circuitry to demodulate and decode responses Supports ISO/IEC 14443 A/MIFARE Typical operating distance in reading/Write mode up to 50 mm

BFD-1000 Five Channel Infrared Tracking Module Tracing Sensor

SKU: 699539 Input voltage: 3.0 V – 5.5 V Output form: digital output (high and low level) Detection distance: 0 – 4 cm (black and white line sensors) 0 – 5 cm (adjustable distance detection)

Analog Sound Sensor Microphone Module for Arduino

SKU: TIFSS0279 Detects various sound signal sizes. Built-in filter-rectifier for stable DC output. Sensitive with adjustable gain. Provides voltage signal for sound intensity. Analog output at VCC/2 amplitude. Arduino compatible.

1/2 Inch Water Flow Sensor - YF-S201

SKU: TIFSS0125 This is the YF-S201 Water flow sensor This sensor is lightweight, small in size, and simple to install. This water flow sensor sits in line with your water line and contains a pinwheel sensor to measure how much water has moved through it. This has an integrated magnetic hall effect sensor that outputs an electrical pulse with every revolution. The hall effect sensor is sealed from the water pipe and allows the sensor to stay safe and dry.

Color Recognition Sensor Module TCS3200D/TCS2300

SKU: TIFSS0027 High-resolution conversion of light intensity to frequency. The pins have 2.54 mm pitch. Mil-convenient for bitmap board. Programmable color and full-scale output frequency. Communicate directly with a microcontroller. Low-profile surface mount package.

Square Force-Sensitive Resistor - Original

SKU: TIFSS0041 Just Connect a resistor to form a voltage devider and meassure the voltage at the junction to find the force applied. These sensors are simple to set up and great for sensing pressure, but they aren't incredibly accurate. Use them to sense if it's being squeezed, but you may not want to use it as a scale.

DHT11 Humidity and Temperature Sensor Module

SKU: TIFSS0029 This is DHT11 Humidity and Temperature Sensor Module The Operating Voltage of the DHT-11 Humidity And Temperature Sensor Module is 3.3VDC to 5.5VDC The DHT-11 Humidity And Temperature Sensor Module is a basic, ultra low-cost digital temperature and humidity sensor DHT11 sensor is good for 20-90% humidity readings. The module can detect the surrounding environment of the humidity and temperature The Module is highly reliability, excellent long-term stability and Low power consumption. The DHT11 Module has fixed bolt hole and easy installation

LM35D Analog Temperature Sensor Module + Cable

SKU: 130267 Based on the semiconductor LM35 temperature sensor Can be used to detect ambient air temperature Calibrated directly in °Celsius (Centigrade) Linear + 10 mV/°C Scale Factor 0.5°C Ensure accuracy (at +25°C) Low power consumption, less than 60uA Low output impedance, 1mA current through only 0.1Ω With screw holes for easy installation and fixed. Aperture 2.6mm

Flex Sensor 2.2 inch

SKU: TIFSS0038 A simple flex sensor 2.2" in length. As the sensor is flexed, the resistance across the sensor increases. The resistance of the flex sensor changes when the metal pads are on the outside of the bend (text on the inside of bend). Connector is 0.1" spaced and bread board friendly. It comes in the form of a thin strip measuring 7.3 cm long and 6.3 mm wide. It has an operating voltage range of 0 to 5V DC. While the Power rating is 0.5Watt (continuous), 1 Watt (peak).

Rain Drop Sensor Module

SKU: TIFSS0140 The LM393, use of the wide voltage comparator that provide both digital and analog output. Treatment of nickel plating and surface, have fight oxidation, electrical conductivity, and life has more superior performance The comparator output, signal clean, good waveform, driving ability is strong, for more than 15 mA With potentiometer sensitivity adjustment and has a fixed bolt hole, convenient installation Output LED indicator. Compatible with Arduino.

KY-036 Metal Touch Sensor

SKU: TIFSS0181 The KY-036 Touch Sensor is a single-channel signal output. This metal touch sensor uses low-level output signal for human body touch sensor alarm. The KY-036 metal sensor has an adjustable sensitivity. This touch sensor is integrated with LM393 chip and working voltage.

Digital Sensor TTP223B Module Capacitive Touch Switch

SKU: 31100 Power supply voltage(VCC): 2.0, 3, 5.5 V. Output high VOH: 0.8VCC V Output low VOL: 0.3VCC V Response time (touch mode) : 60 mS Response time (low power mode) : 220 mS Can replace the traditional touch of a button Four M2 screws positioning holes for easy installation

Soil Moisture Sensor Module

SKU: TIFSS0084 Operating voltage: 3.3V to 5V Dual output mode for more accurate readings Fixed bolt hole for easy installation Power indicator (red) and digital output indicator (green) Highly sensitive for detecting soil moisture Features LM393 comparator chip for stability Digital output (D0) connects directly to MCU for moisture detection

2-Ch 5V Relay Board

SKU: TIFRL0018 5V 10A 2-channel relay module for Arduino, ARM, PIC, AVR Features 4 mounting holes (3.1mm diameter) for easy installation High-quality SPDT relay Status LED: On when active, off when released Can control high load currents: 250V 10A or 125V 15A

12V 1 Channel Relay Module (10Amp)

SKU: TIFRL0056 Isolation groove between the control area and the load area. Has the power and relay action instructions, pull bright, disconnect does not shine. If the input has signal, the beginning of the common and often will have conduction. Can be used as a microcontroller development board and home appliance control.

Heart Rate Pulse Sensor Module

SKU: TIFSS0048 Heart Rate Pulse Sensor Module can be put on the finger or earlobe, through interconnected line can be connected to the Arduino. This Pulse Sensor works with a 3V - 5V Arduino. Essence is an integrated optical amplifying circuit and noise eliminating circuit heart rate sensor. This Pulse Sensor includes the circuits like Amplification & Noise cancellation.

HC-SR501 PIR Motion Detector Sensor Module

SKU: 9251 Wide Working Voltage Range: DC 4.5V- 20V Current Drain: <60uA Detection Angle: <140° Detection Distance: 3 to 7m (can be adjusted) Blockade time: 2.5s (Default) Work temperature: -20-+80°C

MPU-6050 Triple-Axis Accelerometer & Gyroscope Module

SKU: TIFSS0063 16-bit AD converter with 16-bit data output. I2C output for 6 or 9-axis motion fusion data in various formats. Selectable solder jumpers for CLK, FSYNC, and AD0. DMP engine for motion fusion and gesture detection. Automatic bias and compass calibration. Digital-output temperature sensor..

IR Transmitter Receiver Pair

SKU: TIFCC0121 This is the IR Transmitter and Receiver pair matched pair used in our IR proximity, White Line or Micro-mouse sensor. It consists of 5 mm 940 nano-meter wave length high power IR LED. Photo-diode having peak sensitivity at 940 nano-meter wavelength.

MQ-2 Smoke Gas Sensor

SKU: MOD-QC1226

IR (Infrared) Obstacle Avoidance Sensor Module

SKU: TIFSS0154 Detects objects within a range of 2cm to 30cm Easy to set up and use for all skill levels Onboard indicator shows when obstacles are detected Adjustable range with a preset knob for precision Ideal for IoT projects like smart homes and security systems

10A 24V Overcurrent Protection AC Current Detection Sensor Module

SKU: R100746 Product name: Current Detection Sensor Module Current Rating: 10A AC Voltage Rating: 24V Operating Temperature: -40°C ~ +85°C

GOSLING 0-5V to 4-20mA Voltage-Current Converter

SKU: 1121308 power supply: DC 7-30 V Input Voltage: 0-10V Output current: 4-20mA

5A 12V Overcurrent Protection Sensor Module

SKU: 400224 LC 5A Over-current protection Sensor module uses a current transformer to collect the AC signal to achieve the relay over-current signal output within 0-5A. Relay pull while over-current, relay released while not over-current

ACS712 30A Current Sensor Module

SKU: 12264 Low-noise analog signal path Device bandwidth is set via the new FILTER pin 5 µs output rise time in response to step input current Small footprint, low-profile SOIC8 package 2.1 kVRMS minimum isolation voltage from pins 1-4 to pins 5-8 Supply Voltage: 4.5V~5.5V DC Measure Current Range: 30A Sensitivity: 100mV/A

MQ-136 H2S Gas Sensor Module

SKU: 975811 Dual signal output (analog output and TTL level output) The TTL output effective signal is low. Analog output 0 ~ 5V voltage, the higher the concentration the higher the voltage. Good sensitivity to hydrogen sulfide, liquefied gas, natural gas, city gas, and smoke. with long service life and reliable stability fast response recovery characteristics

MQ-137 NH3 Ammonia Gas Sensor Module

SKU: 975812 Wide detecting scope Fast response (less than 1s) High sensitivity( 3%) the circuit voltage: DC5V Stable and long life Operating Voltage is +5V Detect/Measure NH3, Ammonia

MQ-8 Hydrogen H2 Gas Sensor Alarm Detection Module

SKU: 44008 Using high-quality dual-panel design, with power indicator and TTL signal output instructions. The switching signal having a DO (TTL) output and analog output AO. TTL output valid signal is low. The higher the voltage, the concentration of the analog output voltage is higher. A hydrogen gas detection with good sensitivity. Has a long life and reliable stability

MQ-4 Methane CNG Gas Detector High Sensitivity Module

SKU: 9773 Detecting range: 300~10000ppm Signal output indicator. Dual Signal output (analog output and TTL output). The TTL output signal is low level, allows us to connect with SCM directly. Analog output 0~5V voltage. Quick response and recovery.

MQ-9 CO, Methane & LPG Gas Sensor Module

SKU: 43970 Good sensitivity to CO/Combustible Gas High sensitivity to Methane, Propane, and CO Long life and low cost Simple drive circuit Input voltage: DC 5±0.2V Current Consumption: 150mA

MQ-6 Propane Isobutane LPG Gas Sensor Module

SKU: 9772 Model: MQ-6 Operating Voltage: 5V DC Detecting Range:200-10000 ppm Relative Humidity:<95% RH

MQ-5 Methane LPG Propane Gas Sensor Module

SKU: 9771 Model: MQ-5 Operating Voltage: 5V DC Operating Temparature:-20~40 degree celcius

MQ-3 Alcohol Gas Detector Sensor Module

SKU: 29770 Power requirements: 5 VDC @ ~165 mA (heater on) / ~60 mA (heater off). Current Consumption: 150mA. DO output: 0.1 and 5V. AO output: 0.1- 0.3 V (relative to pollution), the maximum concentration of a voltage of about 4V Detecting Concentration: 0.05-10mg/L Alcohol.

MQ-7 CO Carbon Monoxide Gas Sensor Module

SKU: 44007 Operating voltage: DC 5 V. The analog output voltage, the higher the concentration the higher the voltage. The carbon monoxide detection with better sensitivity. With a long service life and reliable stability. Rapid response and recovery characteristics. Range: 10 to 1000 ppm.

MQ-2 Smoke LPG Butane Hydrogen Gas Sensor Module

SKU: 9765 Operating Voltage:+5V Preheat Duration:20 s Analog Output Voltage:0 to 5 V Dimension:36x20x21 mm

Waveshare Flame Sensor

SKU: 1219066 Spectrum range: 760nm ~ 1100nm Detection angle: 0 – 60 degree Power: 3.3V ~ 5.3V Operating temperature: -25℃ ~ 85℃ Dimension: 27.3mm * 15.4mm Mounting holes size: 2.0mm

Fire Flame detection Sensor Relay Module

SKU: 618469 Can detect the fire flame or the wavelength at 760 nm to 1100 nm Test flame lighters distance of 80cm, the larger the flame, the greater the distance test The detection angle of 60 degrees, the flame spectrum particularly sensitive Sensitivity adjustable.

Flame Sensor Module

SKU: 31320 Comparator chip LM393 makes module readings stable. Operating voltage 3.3V-5V. Fast Response Time Sensitivity adjustable Detects a flame or a light source of a wavelength in the range of 760nm-1100 nm. Detection range: up to 100 cm. Adjustable detection range. Detection angle about 60 degrees, it is sensitive to the flame spectrum.

801S Vibration Shock Sensor Module

SKU: 43743 Has a signal output instruction When the output valid signal is high, the light goes out The sensitivity is adjustable (fine-tuning) The wide detection range of vibration, no direction With mounting holes, firmware installation is flexible and convenient.

Female to Female DuPont Line 40 Pin 30cm

SKU: 31321

10 CM 40 Pin Dupont Cable Male/Male, Male/Female, Female/Female Cable Combo

SKU: 76277 40P color DuPont line Length: 100mm Weight: 20~25 gm each Compatible with 2.54mm spacing pin headers 40pcs chromatic color jump wire High quality and in good working condition Durable and reusable Easy to install and use

Male To Male Jumper Wires 40 Pcs 10cm

SKU: 44281

Male to Female Jumper Wires 40Pcs 20cm

SKU: 7450 40P colored jumper wires Length: 200mm Weight: 30 gm Compatible with 2.54mm spacing pin headers High quality and in good working condition Durable and reusable Easy to install and use

Universal 4×4 16 Key Matrix Membrane Switch Keypad Keyboard

Ultra-thin design & adhesive backing provides easy integration to any project Excellent price-performance ratio Easy communication with any microcontroller 5 pins 2.54mm pitch connector, 4x 4type 16 keys. Sticker can peel off for adhesive mounting. Operating Voltage (V): 5 DC

Active Buzzer Alarm Module DC 3.3-5V

An Active Buzzer Module DC 3.3-5V for Arduino is an audio signaling device, which may be mechanical, electro-mechanical, or piezoelectric. Just like what you are viewing now, it is 3.3V-5V DC Electronic Part Active Buzzer Module. Using top quality material, it is durable in use. An active buzzer rings out as long as it is electrified. Compared with a passive buzzer, it is a bit expensive but easier to control. Typical uses of buzzers include alarm devices, timers, and confirmation of user input such as a mouse click or keystroke.

PS2 Joystick Module Breakout Sensor

2.54mm pin interface leads Long service life and stable performance Standard interface and electronic building blocks Widely use in Arduino DIY projects Cross rocker as a two-way 10K resistor, with the rocker in a different direction.

Breadboard with Solderless 400 points

400 Tie Points – Solderless Breadboard is a high-quality breadboard with power lanes and printed top face for easy prototyping. A breadboard is used to make up temporary circuits for testing or to try out an idea. No soldering is required so it is easy to change connections and replace components.

MQ 135 Air Quality/Gas Detector Sensor Module

The MQ-135 Air Quality/Gas Detector Sensor Module is a cost-effective semiconductor sensor used to detect various harmful gases and volatile organic compounds (VOCs) in the air. It is widely used in hobbyist projects and low-cost air quality monitoring applications.

Raindrop Detection Sensor Module Rain Sensor

The raindrop detection sensor module is a low-cost, Arduino-compatible tool designed to detect rain or water presence through a resistive sensing board (55 x 40 mm). It features an LM393 comparator module for sensitivity adjustment, providing both analog (voltage level) and digital (wet/dry) outputs for automation, such as smart wipers or weather stations.

Humidity Sensitive Switch Relay Module

A Humidity Sensitive Switch Relay Module is an electronic component that automatically controls connected devices by turning a relay on or off based on a pre-set ambient humidity level. These modules typically use a high-quality HR202 humidity sensor and feature an adjustable potentiometer to set the desired humidity threshold.

jumpur wire

Adafruit LPS22 Pressure Sensor – STEMMA QT / Qwiic – LPS22HB

SKU: R218548 Range: 260-1260 hPa Accuracy: ±0.1 hPa Speed: 75 readings/second Compatibility: 3.3V & 5V devices

Pressure sensor module interposer

SKU: R192186 Model: HX710B Pressure Measurement Range: 0 to 40 kPa Operating Voltage: 3.3V to 5V Operating Temperature Range: -40°C to +85°C Gain Options: Selectable gains of 32, 64, and 128 Data Output Rate: 10 SPS / 80 SPS Package Type: 16-pin SOP

RFP Thin Film Pressure Sensor Resistance/Voltage Conversion Module Analog Circuit adapted to FSR4 Series

SKU: R240170 Converts resistance to analog voltage Dual output: analog (AO) + digital (DO) Works with 3.3V & 5V systems Small size: 1.4 × 3.2 cm Ideal for FSR4 series pressure sensors

BMP388 Digital Atmospheric Pressure Sensor Module

The BMP388 is a high-precision, low-power, and low-noise barometric pressure sensor

Digital LDR Light Sensor Module for Arduino

It comes with an M3 mounting hole for ease of attaching it to an object. Onboard, it provides an LDR, high sensitivity and commonly being used for light detection. The module comes with a power LED and a status LED as an indicator.

GY-31 TCS3200 Color Sensor Module

This Product is available in two different variants (GY-31 and HW-531) with the same working we will ship it randomly.

Waveshare Sound Sensor

This is a Waveshare Sound Sensor. LM386 is an audio power amplifier with features of low power consumption, adjustable voltage gain, wide voltage power supply, fewer requirements on peripheral components, and minimum total harmonic distortion.

Sound Detection Sensor Module for Arduino Robots Rated

A Single channel signal output Sensor

PIR (Passive Infrared) Motion Sensor Detector Module

A PIR sensor (Passive Infrared sensor) detects motion by sensing changes in infrared (heat) radiation from objects like people or animals, rather than emitting its own signals, making it energy-efficient and ideal for security systems, automatic lights, and doorbells

HC-SR04 Ultrasonic Distance Sensor Module